The tables below describe the information that is derived from the SKM Format file. There are three sources of data that are used to create the imported data in EasyPower:
Please note the following:
| Bus | ||||
|---|---|---|---|---|
| Area/Tab | Data | Imported | Calculated | Mapped |
| Specifications | Bus Type | X | ||
| Rating (A) | X | |||
| Bracing (kA) | X | |||
| Arc Flash Hazard | AF For This Bus |
X (if Excluded) |
||
| Cable | ||||
|---|---|---|---|---|
| Area/Tab | Data | Imported | Calculated | Mapped |
| Specifications 1 | Unit |
X (See note below) |
||
| No/Ph | X | |||
| Type | X | |||
| Insulation | X | |||
| Size | X | |||
| Conductor Material (Copper/Aluminum) | X | |||
| Length (ft) | X | |||
| Insulation Level | X | |||
| Impedances (all) |
X (See note below) |
X |
||
| Rating (A) | X | |||
| Raceway Type | X | |||
| Raceway Material | X | |||
| Specifications 2 | Ambient Temp (C) | X | ||
| Duct Config | X | |||
| Conduit Size | X | |||
| Conduit Num | X | |||
| Ground Wire | Type (None/Interstitial/Separate/Group) | X | ||
| Num | X | |||
| Size | X | |||
| Material (Copper/Aluminum) | X | |||
| Insulation | X | |||
| Neutral Wire | Num | X | ||
| Size | X | |||
| Material (Copper/Aluminum) | X | |||
| Insulated | X | |||
| Rating | X | |||
Note: If the cable cannot be mapped, the Unit is set to Per Unit, and per unit impedances are imported.
| Fused Switch | ||||
|---|---|---|---|---|
| Area/Tab | Data | Imported | Calculated | Mapped |
| Connection Info | Open/Closed | X | ||
| Base kV | X | |||
| Specifications | Mfr | X | ||
| Type | X | |||
| Style | X | |||
| Model | X | |||
| Library | X | X | ||
| Size | X | |||
| Short Circuit | Fused Interrupting (kA) | X | ||
| Text X/R | X | |||
| HV Breaker | ||||
|---|---|---|---|---|
| Area/Tab | Data | Imported | Calculated | Mapped |
| Connection Info | Open/Closed | X | ||
| Specifications | Mfr | X | ||
| Type | X | |||
| Style | X | |||
| Continuous Current | X | |||
| Short Circuit | Max kV | X | ||
| Rated kA @ Max kV | X | |||
| Interrupting | X | |||
| Close & Latch (kA) | X | |||
| K-factor | X | |||
| Cycles | X | |||
| Load | ||||
|---|---|---|---|---|
| Area/Tab | Data | Imported | Calculated | Mapped |
| Specifications | Load Unit | X | ||
| Constant MVA MW | X | |||
| Constant I MW | X | |||
| Constant Z MW | X | |||
| Constant MVA MVAR | X | |||
| Constant I MVAR | X | |||
| Constant Z MVAR | X | |||
| LV Breaker | ||||
|---|---|---|---|---|
| Area/Tab | Data | Imported | Calculated | Mapped |
| Connection Info | Open/Closed | X | ||
| Specifications | Class (LVPCB/ICCB/MCCB) | X | ||
| Breaker Mfr | X | |||
| Breaker Type | X | |||
| Breaker Style | X | |||
| Trip | X | |||
| Solid State Trip Mfr | X | |||
| Solid State Trip Type | X | |||
| Solid State Trip Style | X | |||
| Sensor | X | X | ||
| Plug | X | X | ||
| Short Circuit | Interrupting (kA) | X | ||
| Phase Trip | LTPU Setting (C) | X | ||
| LTPU Mult | X | |||
| LTPU Band | X | |||
| STPU Pickup | X | |||
| STPU (I^x) t | X | |||
| STPU Delay | X | |||
| Instantaneous Enable Override | X | |||
| Instantaneous Pickup | X | |||
| Gnd Trip | Ground Trip Pickup | X | ||
| Ground Trip (I^x) | X | |||
| Ground Trip Delay | X | |||
| Maint-GF Pickup | X | |||
| Motor | ||||
|---|---|---|---|---|
| Area/Tab | Data | Imported | Calculated | Mapped |
| Connection Info | Model (Individual/Group) | X | ||
| Specifications | Unit | X | ||
| kV | X | |||
| HP | X | |||
| Sync RPM | X | |||
| kVA FLA | X | |||
| kVA PF | X | |||
| kVA Eff | X | |||
| Service Factor | X | |||
| One-line Graphics With AFD | X | |||
| One-line Graphics Type | X | |||
| Short Circuit | Impedance ANSI Code | X | ||
| X/R | X | |||
| X"dv or Xlr | X | |||
| Power Flow | Load Type (kVA/Current/Impedance/kW+jl) | X | ||
| Panels | ||||
|---|---|---|---|---|
| Area/Tab | Data | Imported | Calculated | Mapped |
| Description | Panel Load Units | X | ||
| Circuit Number | X | |||
| Load Description | X | |||
| CB/Fuse Poles | X | |||
|
Amps (A), Amps (B), Amps (C), or VA (A), VA (B), VA (C) Note: Data imported depends on the panel load units selected. |
X | |||
| PF | X | |||
| Trip (A) | X | |||
| Library Load | X | |||
| kV | X | |||
| Switch | ||||
|---|---|---|---|---|
| Area/Tab | Data | Imported | Calculated | Mapped |
| Specifications | Mfr | X | ||
| Type | X | |||
| Style | X | |||
| Continuous Current | X | |||
| Short Circuit | Momentary/C&L (kA) | X | ||
| Two Winding Transformer | ||||
|---|---|---|---|---|
| Area/Tab | Data | Imported | Calculated | Mapped |
| Connection Info | From Bus: Base kV | X | ||
| To Bus: Base kV | X | |||
| From Bus: Conn (D/Y/YG) | X | |||
| To Bus: Conn (D/Y/YG) | X | |||
| Specifications | Unit | X | ||
| Type | X | |||
| Class | X | |||
| Temp | X | |||
| Form (Core/Shell) | X | |||
| Winding Information: Rated KV From | X | |||
| Winding Information Rated kV To | X | |||
| Tap kV From | X | |||
| Tap kV To | X | |||
| kVA Rating | X | |||
| kVA O/L | X | |||
| Impedance | Z% | X | ||
| Z0% | X | |||
| X/R Ratio | X | |||
| Grounding R From Side | X | |||
| Ground R To Side | X | |||
| Ground jX From Side | X | |||
| Ground jX To Side | X | |||
| Ground Amp Class From Side | X | |||
| Ground Amp Class To Side | X | |||
| TCC | Magnetizing Inrush Rated FLA | X | ||
| Magnetizing Inrush Cycles | X | |||
| Utility | ||||
|---|---|---|---|---|
| Area/Tab | Data | Imported | Calculated | Mapped |
| Specifications | Utility kV | X | ||
| Fault Duty Unit | X | |||
| 3 Phase Short Circuit Values | X | |||
| SLG Short Circuit Values | X | |||
| Power Flow | Model (Swing/PV/PQG) | X | ||
| Ctl kV PU | X | |||
| Ctl Angle | X | |||
| Ctrl Bus | X | |||
| Base kV | X | |||
| MW | X | |||
|
MVAR |
X | |||
| MVAR Min | X | |||
| MVAR Max | X | |||
The following items are imported but data is not currently included:
Note: Capacitors are imported as filters.
The following items are not currently imported but may be in the future:
| Using EasyPower with Other Programs | |
| Creating an SKM Data Export CSV File | |
| Using Customized Mappings |
|
|